One mounts, the other doesn't :-(
Today’s mystery is why a USB won’t mount, I have two identical USB sticks, one mounts as soon as it’s plugged in, the other isn’t recognised.
I can find my way to it with gparted to format it, but I can’t get the stick to mount, yet the other identical stick does.
I’d appreciate any pointers, not sure if the info below helps ?
[255668.093489] usb 1-4: Product: USB Flash Drive
[255668.093492] usb 1-4: Manufacturer: Philips
[255668.093494] usb 1-4: SerialNumber: 0708648D1F1C7440
[255668.095178] usb-storage 1-4:1.0: USB Mass Storage device detected
[255668.095543] scsi host0: usb-storage 1-4:1.0
[255669.116473] scsi 0:0:0:0: Direct-Access Philips USB Flash Drive PMAP PQ: 0 ANSI: 6
[255669.116920] sd 0:0:0:0: Attached scsi generic sg0 type 0
[255669.117366] sd 0:0:0:0: [sda] 30302208 512-byte logical blocks: (15.5 GB/14.4 GiB)
[255669.117596] sd 0:0:0:0: [sda] Write Protect is off
[255669.117599] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
[255669.117852] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[255669.341478] sda:
[255669.343461] sd 0:0:0:0: [sda] Attached SCSI removable disk
[255683.586593] sda:
[255683.784285] sda:
[258726.286135] usb 1-4: USB disconnect, device number 41
[258890.759943] wlp0s20f3: authenticate with 20:b0:01:c5:39:55
[258890.762287] wlp0s20f3: send auth to 20:b0:01:c5:39:55 (try 1/3)
[258890.787586] wlp0s20f3: authenticated
[258890.790734] wlp0s20f3: associate with 20:b0:01:c5:39:55 (try 1/3)
[258890.795208] wlp0s20f3: RX AssocResp from 20:b0:01:c5:39:55 (capab=0x1011 status=0 aid=6)
[258890.798847] wlp0s20f3: associated
[258890.846434] wlp0s20f3: Limiting TX power to 20 (20 - 0) dBm as advertised by 20:b0:01:c5:39:55
[258924.342901] wlp0s20f3: deauthenticated from 20:b0:01:c5:39:55 (Reason: 2=PREV_AUTH_NOT_VALID)
[258925.002597] wlp0s20f3: authenticate with 22:b0:01:c5:39:5d
[258925.006221] wlp0s20f3: send auth to 22:b0:01:c5:39:5d (try 1/3)
[258925.029405] wlp0s20f3: authenticated
[258925.029587] wlp0s20f3: associate with 22:b0:01:c5:39:5d (try 1/3)
[258925.031450] wlp0s20f3: RX AssocResp from 22:b0:01:c5:39:5d (capab=0x1011 status=0 aid=1)
[258925.033625] wlp0s20f3: associated
[258925.112644] wlp0s20f3: Limiting TX power to 23 (23 - 0) dBm as advertised by 22:b0:01:c5:39:5d
[259930.439233] usb 1-4: new high-speed USB device number 42 using xhci_hcd
[259930.712925] usb 1-4: New USB device found, idVendor=13fe, idProduct=5400, bcdDevice= 1.10
[259930.712930] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[259930.712933] usb 1-4: Product: USB Flash Drive
[259930.712936] usb 1-4: Manufacturer: Philips
[259930.712938] usb 1-4: SerialNumber: 0708648D1F1C7440
[259930.714721] usb-storage 1-4:1.0: USB Mass Storage device detected
[259930.715356] scsi host0: usb-storage 1-4:1.0
[259931.740845] scsi 0:0:0:0: Direct-Access Philips USB Flash Drive PMAP PQ: 0 ANSI: 6
[259931.741427] sd 0:0:0:0: Attached scsi generic sg0 type 0
[259931.742510] sd 0:0:0:0: [sda] 30302208 512-byte logical blocks: (15.5 GB/14.4 GiB)
[259931.742779] sd 0:0:0:0: [sda] Write Protect is off
[259931.742782] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
[259931.743040] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[259931.975830] sda:
[259931.977896] sd 0:0:0:0: [sda] Attached SCSI removable disk
[263163.619800] debugfs: File 'le_min_key_size' in directory 'hci0' already present!
[263163.619803] debugfs: File 'le_max_key_size' in directory 'hci0' already present!
[264345.945496] wlp0s20f3: authenticate with 20:b0:01:c5:39:55
[264345.948447] wlp0s20f3: send auth to 20:b0:01:c5:39:55 (try 1/3)
[264345.973684] wlp0s20f3: authenticated
[264345.977144] wlp0s20f3: associate with 20:b0:01:c5:39:55 (try 1/3)
[264345.981156] wlp0s20f3: RX AssocResp from 20:b0:01:c5:39:55 (capab=0x1011 status=0 aid=6)
[264345.983554] wlp0s20f3: associated
[264346.075021] wlp0s20f3: Limiting TX power to 20 (20 - 0) dBm as advertised by 20:b0:01:c5:39:55
[264399.048050] wlp0s20f3: deauthenticated from 20:b0:01:c5:39:55 (Reason: 2=PREV_AUTH_NOT_VALID)
[264399.825591] wlp0s20f3: authenticate with 22:b0:01:c5:39:5d
[264399.829457] wlp0s20f3: send auth to 22:b0:01:c5:39:5d (try 1/3)
[264399.853133] wlp0s20f3: authenticated
[264399.855456] wlp0s20f3: associate with 22:b0:01:c5:39:5d (try 1/3)
[264399.857190] wlp0s20f3: RX AssocResp from 22:b0:01:c5:39:5d (capab=0x1011 status=0 aid=1)
[264399.859316] wlp0s20f3: associated
[264399.921321] wlp0s20f3: Limiting TX power to 23 (23 - 0) dBm as advertised by 22:b0:01:c5:39:5d
[265724.844270] usb 1-4: USB disconnect, device number 42
[265731.535908] usb 1-4: new high-speed USB device number 43 using xhci_hcd
[265731.800911] usb 1-4: New USB device found, idVendor=13fe, idProduct=5400, bcdDevice= 1.10
[265731.800916] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[265731.800919] usb 1-4: Product: USB Flash Drive
[265731.800921] usb 1-4: Manufacturer: Philips
[265731.800923] usb 1-4: SerialNumber: 0708648D1F1C7440
[265731.802641] usb-storage 1-4:1.0: USB Mass Storage device detected
[265731.802970] scsi host0: usb-storage 1-4:1.0
[265732.813637] scsi 0:0:0:0: Direct-Access Philips USB Flash Drive PMAP PQ: 0 ANSI: 6
[265732.814213] sd 0:0:0:0: Attached scsi generic sg0 type 0
[265732.815154] sd 0:0:0:0: [sda] 30302208 512-byte logical blocks: (15.5 GB/14.4 GiB)
[265732.815386] sd 0:0:0:0: [sda] Write Protect is off
[265732.815390] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
[265732.815616] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[265733.040330] sda:
[265733.042237] sd 0:0:0:0: [sda] Attached SCSI removable disk
[266438.743760] usb 1-4: USB disconnect, device number 43
[266451.662384] usb 1-4: new high-speed USB device number 44 using xhci_hcd
[266451.875430] usb 1-4: New USB device found, idVendor=13fe, idProduct=5400, bcdDevice= 1.10
[266451.875435] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[266451.875438] usb 1-4: Product: USB Flash Drive
[266451.875440] usb 1-4: Manufacturer: Philips
[266451.875442] usb 1-4: SerialNumber: 0708648B241B9F07
[266451.877227] usb-storage 1-4:1.0: USB Mass Storage device detected
[266451.877661] scsi host0: usb-storage 1-4:1.0
[266452.887929] scsi 0:0:0:0: Direct-Access Philips USB Flash Drive PMAP PQ: 0 ANSI: 6
[266452.888605] sd 0:0:0:0: Attached scsi generic sg0 type 0
[266452.889529] sd 0:0:0:0: [sda] 30302208 512-byte logical blocks: (15.5 GB/14.4 GiB)
[266452.889825] sd 0:0:0:0: [sda] Write Protect is off
[266452.889828] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
[266452.890094] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[266453.038584] sda: sda1
[266453.041349] sd 0:0:0:0: [sda] Attached SCSI removable disk
[266453.266472] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[266765.543022] usb 1-4: USB disconnect, device number 44
[266774.376489] usb 1-4: new high-speed USB device number 45 using xhci_hcd
[266774.654350] usb 1-4: New USB device found, idVendor=13fe, idProduct=5400, bcdDevice= 1.10
[266774.654355] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[266774.654358] usb 1-4: Product: USB Flash Drive
[266774.654360] usb 1-4: Manufacturer: Philips
[266774.654362] usb 1-4: SerialNumber: 0708648D1F1C7440
[266774.656180] usb-storage 1-4:1.0: USB Mass Storage device detected
[266774.656509] scsi host0: usb-storage 1-4:1.0
[266775.662115] scsi 0:0:0:0: Direct-Access Philips USB Flash Drive PMAP PQ: 0 ANSI: 6
[266775.662729] sd 0:0:0:0: Attached scsi generic sg0 type 0
[266775.663659] sd 0:0:0:0: [sda] 30302208 512-byte logical blocks: (15.5 GB/14.4 GiB)
[266775.663908] sd 0:0:0:0: [sda] Write Protect is off
[266775.663911] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
[266775.664136] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[266775.892029] sda:
[266775.894530] sd 0:0:0:0: [sda] Attached SCSI removable disk
[266927.234368] usb 1-4: USB disconnect, device number 45
[266966.391195] usb 1-4: new high-speed USB device number 46 using xhci_hcd
[266966.672120] usb 1-4: New USB device found, idVendor=13fe, idProduct=5400, bcdDevice= 1.10
[266966.672124] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[266966.672127] usb 1-4: Product: USB Flash Drive
[266966.672130] usb 1-4: Manufacturer: Philips
[266966.672132] usb 1-4: SerialNumber: 0708648D1F1C7440
[266966.673858] usb-storage 1-4:1.0: USB Mass Storage device detected
[266966.674240] scsi host0: usb-storage 1-4:1.0
[266967.688572] scsi 0:0:0:0: Direct-Access Philips USB Flash Drive PMAP PQ: 0 ANSI: 6
[266967.689144] sd 0:0:0:0: Attached scsi generic sg0 type 0
[266967.689907] sd 0:0:0:0: [sda] 30302208 512-byte logical blocks: (15.5 GB/14.4 GiB)
[266967.690141] sd 0:0:0:0: [sda] Write Protect is off
[266967.690145] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
[266967.690387] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[266967.927993] sda:
[266967.929617] sd 0:0:0:0: [sda] Attached SCSI removable disk
[email protected]:~$
About author
You might also like
[ubuntu_studio] Ubuntu Studio 20.10 customisations?
Hi, I have just installed and started to explore Ubuntu Studio 20.10. There are 2 things up front I’d like to customise. Since I don’t know how to do it,
Audio Outputs detected inconsistently
HI all, I’m having an issue where my audio outputs are not detected consistently. I generally either use 1. HDMI audio out (monitor speakers) 2. Headset (via audio jack) The
how to change the sudo cmd timeout?
hi how do you change the time that sudo is active with having to re-input passwd? also how to make it so you have to put the passwd in everytime?
0 Comments
No Comments Yet!
You can be first to comment this post!